Difference between revisions of "Linux video capture over firewire (IEEE1394)"
m |
m (→Process) |
||
| (2 intermediate revisions by the same user not shown) | |||
| Line 4: | Line 4: | ||
apt-get -y install dvgrab libraw1394-8 libavc1394-0 libiec61883-0 | apt-get -y install dvgrab libraw1394-8 libavc1394-0 libiec61883-0 | ||
| + | |||
| + | ==Process== | ||
| + | In order to do DV video we use [http://www.linux1394.org/ libraw1394] to import a digital video stream from the camera and also to give it commands like ''pause'', ''record'' and ''fast-forward'' (known as AVC commands). | ||
Plug the firewire PCI card into the PC and boot up. | Plug the firewire PCI card into the PC and boot up. | ||
| Line 12: | Line 15: | ||
This tells you that linux has registered the card and has activated two interfaces: A firewire host controller and an Ethernet over firewire device. | This tells you that linux has registered the card and has activated two interfaces: A firewire host controller and an Ethernet over firewire device. | ||
| − | This is a potential problem because I don't want to use firewire for networking. | + | This is a potential problem because I don't want to use firewire for networking. In my case the firewire ethernet driver was binding to the camera device, preventing ''dvgrab'' from being able to record the video. So we disable the 1394 ethernet driver with: |
| + | rmmod eth1394 | ||
| + | |||
| + | It's possible to set this to be the default behavior, perhaps in ''/etc/modprobe.d/blacklist''. Now do this: | ||
| + | tail -f /var/log/messages | ||
| + | Power on the DV camera and plug it into the firewire port. Something like this should appear on the console. | ||
| + | Nov 8 14:41:51 colourbox kernel: ieee1394: raw1394: /dev/raw1394 device initialized | ||
| + | |||
| + | This means the ''raw1394'' driver has connected to the camera. You're ready to capture some video. | ||
| + | dvgrab --format raw --noavc foo | ||
| − | + | This will begin capturing from DV immediately in raw DV format, naming the files beginning with ''foo...'' in the current directory. | |
| + | |||
| + | You can then use ''mplayer'' to play back the DV stream. | ||
Latest revision as of 00:46, 9 November 2008
Packages
You may need to add the debian multimedia repository to your sources list.
apt-get -y install dvgrab libraw1394-8 libavc1394-0 libiec61883-0
Process
In order to do DV video we use libraw1394 to import a digital video stream from the camera and also to give it commands like pause, record and fast-forward (known as AVC commands).
Plug the firewire PCI card into the PC and boot up.
grep 1394 /var/log/messages Nov 8 11:49:09 colourbox kernel: ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[42100000-421007ff] Max Packet=[2048] IR/IT contexts=[4/8] Nov 8 11:49:09 colourbox kernel: eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
This tells you that linux has registered the card and has activated two interfaces: A firewire host controller and an Ethernet over firewire device.
This is a potential problem because I don't want to use firewire for networking. In my case the firewire ethernet driver was binding to the camera device, preventing dvgrab from being able to record the video. So we disable the 1394 ethernet driver with:
rmmod eth1394
It's possible to set this to be the default behavior, perhaps in /etc/modprobe.d/blacklist. Now do this:
tail -f /var/log/messages
Power on the DV camera and plug it into the firewire port. Something like this should appear on the console.
Nov 8 14:41:51 colourbox kernel: ieee1394: raw1394: /dev/raw1394 device initialized
This means the raw1394 driver has connected to the camera. You're ready to capture some video.
dvgrab --format raw --noavc foo
This will begin capturing from DV immediately in raw DV format, naming the files beginning with foo... in the current directory.
You can then use mplayer to play back the DV stream.
